• lift hydraulic high performance cylinder

    VSL | Post-tensioning strand systems | Post tension

    Post-tensioning strand systems. VSL designs, manufactures and installs durable, state-of-the-art post-tensioning systems that comply with international standards and approval guidelines for both new and existing structures.

  • pneumatic solenoid valve CDG5BN25S smc air regulator

    Monostrand Post-Tensioning System - DSI USA

    An open throat, twin ram jack for stressing 0.5 (12.7 mm) or 0.6 (15.2 mm) single strand is suitable for stressing at tendon ends or at intermediate tendon anchors. For tendon elongation greater than the stroke of the jack, the wedges are temporarily seated after partial stressing and the jack is recycled.

  • China high quality telescopic jacks

    Post Tensioning Chucks - Prestress Supply

    All tension components for the systems are designed to develop 100% of the bar strength. All components of the systems are designed and manufactured in the United States. Williams All-Thread-Bar systems have been field proven around the world. • Transverse Post Tensioning • Longitudinal Post Tensioning • Pile Test Anchors • Rock Anchors

  • synchronous lifting heavy equipment hydraulic cylinder

    Post Tension Used Anchor, Post Tension Used Anchor

    Post-Tensioning Chucks Our post-tensioning chucks are manufactured under strict tolerances and quality control and meet or exceed the requirements of the Post-Tension Institute and International Building Code. Chuck sizes include .600″, 1/2″, 7/16″ and 3/8″ . All post-tension chucks come with a two-piece wedge. Three-piece wedges are available upon request.

  • solenoid coil VG342-4G-10A pneumatic cylinder actuator

    Stressing Equipment - Post Tensioning System

    GLOSSARY OF POST-TENSIONING TERMS April 6, 2007 Page 4 of 20 Active-End Anchorage: Anchorage at the end of a tendon where the stressing jack is attached to the tendon during stressing operations. Added Tendons: Tendons, usually short in length, placed in specific locations such as end bays to increase the structural capacity at that location without having to use full-length

  • DC12V pallet truck Power Unit

    BBR | What is post-tensioning?

    .com offers 162 post tension used anchor products. About 18% of these are anchors, 3% are bolts. A wide variety of post tension used anchor options are available to you, such as free samples.

  • two stroke cylinder for trailer

    Detensioning Unbonded Post-Tension Tendons - Amsysco Inc.

    Stressing Jack is the multistrand jack with capacity of 100 to 1,500 tonnes. And Lifting Jack is for heavy lifting purposes. Bond Head and Compression Fitting Machine is the equipment for making fixed anchors (dead anchors) in post tensioning.

  • lock hydraulic jack

    concrete prestressed jack anchor post tensioning/pc strand

    Jack (b) Tensioning of tendons Anchor (c) Anchoring the tendon at the stretching end Figure 1-4.4 Stages of post-tensioning (shown in elevation) 1.4.3 Advantages of Post-tensioning The relative advantages of post-tensioning as compared to pre-tensioning are as follows. • Post-tensioning is suitable for heavy cast-in-place members.

  • Agricultrual Hydraulic Cylinder Manufacturers

    SJ: 20 - 30T Post Tension/Stressing Jack | Power Team

    Perhaps the most dramatic example of design flexibility is demonstrated by the use of post-tensioning for bridges where it allows very demanding geometry requirements, including complex curves, variable superelevation and significant grade changes. In stadiums, post-tensioning allows long clear spans and a highly creative architectural approach.

  • original pneumatic smc pneumatics china factory new

    Jul 28, 2011· Detensioning Unbonded Post-Tension Tendons. Posted on July 28, 2011 by Neel Khosa. On rare occasions, the ironworker/installer will need to detension an already-stressed post tensioning tendon. The reason may be due to a repair procedure or re-stressing due to out-of-range elongation readings. ... to take wedges out of anchor cavity. Do not use ...

  • 2 Ton Standard Low Profile Bottle Jack

    • ALWAYS USE AND FOLLOW THE LATEST REvISION OF THE POST-TENSIONING INSTITUTE FIELD PROCEDURES MANUAL FOR BONDED SINGLE STRAND TENDONS (AvAILABLE FROM POWER TEAM - #107348) WHEN USING THESE POST-TENSIONING JACKS. • A double-acting jack must have both hoses and all couplers securely connected to both ports.

  • center hole hydraulic jack

    ♦ YCW-series light stressing jack is a kind of general-purpose feed-through jack for prestress applied for tension of various steel strand anchors. ♦ Tension jack is widely used in post-tensioned large buildings and structures, prestressed concrete bridges, rock and earth anchoring construction, hydraulic structures, foundation anchoring ...

  • DC12V 24V tipper trailer Power Unit

    Order Number Description Cylinder Capacity (tons) Stroke (mm.) Seater Type. Metric Tons at 700 bar. Weight (kg.) SJ2010: Post tension jack with spring seater, 12,7 mm strand.

  • power pack hydraulic jack

    diameter strands started to be used, and the system of multiple and simultaneous tensioning was developed. The use of strand, at that time scarcely present in post-tensioning, made it possible to carry out a system of multiple tensioning which, by assuring the isotensioning to cable components under stressing, complied with a design requirement,

Our Factory

Founded in 2012, Gaode Equipment Co., Ltd. (short:“Gaodetec”) owns the most advanced imported production equipment and complete production technology...

Read More

Factory Gallery

Contact Us